N-BK7金属镀膜反射镜

晶体最适用于激光应用。 UNI OPTICS提供以下晶体产品。

1.激光晶体和棒：YAG晶体，Nd：YVO4晶体
2.非线性晶体：BBO，KTP，LiNbO3，LBO。KDP＆DKDP
3.双折射晶体：YVO4，a-BBO，方解石。

用于光纤耦合和激光二极管光束成形，工作距离为0mm的透镜非常适用于单模和多模光纤和激光二极管的准直，因为透镜可以直接定位并直接粘合在发射源上。 对于聚焦应用，或者镜头不能与发射源直接接触的情况下，所有镜头也可以具有小的工作距离。UNI Optics可提供Φ1~Φ15mm的尺寸，数量和尺寸，包括抛光/磨削表面的差异，可根据客户要求提供。

1.  Germanium (Ge)

Germanium (Ge) is the preferred lens and window material for high performance infrared imaging systems in the 8–12 μm wavelength band. Its high refractive index makes Ge ideal for low power imaging systems because of minimum surface curvature. Chromatic aberration is small, often eliminating the need for correction.

2. Silicon (Si) 

Silicon (Si) is grown by Czochralski pulling techniques (CZ) and contains some oxygen that causes an absorption band at 9 microns.To avoid this, material can be prepared by a Float-Zone (FZ) process. Optical silicon is generally lightly doped (5 to 40 ohm cm) for best transmission above 10 microns, and doping is usually boron (P-type) and phosphorus (N-type). After doping silicon has a further pass band: 30 to 100 microns which is effective only in very high resistivity uncompensated material.
 
CZ Silicon is commonly used as substrate material for infrared reflectors and windows in the 1.5-8 micron region. The strong absorption band at 9 microns makes it unsuitable for CO2 laser transmission applications, but it is frequently used for laser mirrors because of its high thermal conductivity and low density. Application as window, lens in the 1.5 - 8 um region; Mirror for CO2 laser and spectrometer applications.
 

ZnS MultiSpectral Under intense heat and pressure, defects within the crystalline lattice are virtually eliminated, leaving a water-clear material with minimal scatter and high transmission characteristics from 0.4 to 12 microns. This material is particularly well suited for high-performance common aperture systems that must perform across a broad wavelength spectrum.

Specifications:

Material: ZnS MultiSpectral
Diameter Tolerance: --------------------- +0.0, -0.1mm
Thickness Tolerance: -------------------- ±0.1mm
Clear Aperture: ---------------------------->85%
Parallelism: -----------------------------------3 arc minute
Surface Quality: ----------------------------80-50 scratch and dig
Wavefront Distortion: -------------------- λ /2 per 25mm @633mm
Bevel: -----------------------------------------Protective  (<0.2mm x 45° )
Coating: -------------------------------------- Optional （Uncoated, AR Coating, etc.）

4. ZnSe material

ZnSe is a preferred material for lenses, windows, output couplers and beam expanders for its low absorptivity at infrared wavelengths and its visible transmission. For high-power applications, it’s critical that the material bulk absorption and internal defect structure be carefully controlled, that minimum-damage polishing technology be employed, and the highest quality optical thin-film coatings are used. The material absorption is verified by CO2 laser vacuum calorimetry. Our quality assurance department provides testing and specific optics certification on request.

ZnSe is non-hygroscopic and chemically stable, unless treated with strong acids. It’s safe to use in most industrial field, and laboratory environments.

色散棱镜用于需要将入射光分离成其组成波长的应用中。例如，当白光进入色散棱镜时，它被分成三个部分:红、绿和蓝。色散棱镜是理想的光谱学或激光调谐。

偏振分光棱镜由两个直角棱镜胶合而成，其中一个棱镜的斜面镀有偏振介质膜。当与正常入射、非偏振光一起使用时，入射光被分成两束偏振光，P偏振光可直接穿过，S偏振光以90°角反射出来。